The Christine Car Club

Not a member of the CCC? Come on in and register...membership is FREE!


Dedicated To The Restoration And Maintenance Of The 1957-1958 Plymouth
 
HomeCalendarFAQUsergroupsRegisterLog in
Latest topics
» recommendations for enclosed transport, east cast
Fri Dec 07, 2018 10:55 am by roadrunninMark

» GREAT NEWS FOR THE CCC FORUM!
Wed Dec 05, 2018 1:07 am by JAG

» Article on Christine
Wed Nov 28, 2018 2:24 am by Christinefan824

» Happy Thanksgiving!
Sun Nov 25, 2018 8:22 pm by Bloodhound1958

» C@@L pic of Christine with Danica
Sat Nov 24, 2018 5:36 pm by JAG

» RMS Titanic Control Room Panel
Thu Nov 22, 2018 9:20 am by Bloodhound1958

» Deep Roots
Sat Nov 17, 2018 1:00 pm by furvedere

» Fresh Air Intake?
Fri Nov 16, 2018 9:46 pm by 58belvedere

» Speedometer pinion gear
Thu Nov 15, 2018 1:42 pm by JAG

» Hell Hath No Fury Like Her: The Making of Christine by Lee Gambin
Mon Nov 12, 2018 10:20 pm by ghostsoldier

Search
 
 

Display results as :
 
Rechercher Advanced Search
John Carpenter Shout Out!
Alexandra Paul Shout Out!
Christine Movie Soundtrack
Share | 
 

 sheet metal?

View previous topic View next topic Go down 
AuthorMessage
crazy58fury
CCC Member
CCC Member
avatar

Posts : 264
Points : 322
Reputation : 0
Join date : 2012-01-26
Age : 23
Location : Rochester, NY

PostSubject: sheet metal?   Mon Jun 25, 2012 1:03 pm

Hey guys, I had a question about the gage of sheet metal the body is? And what gage is the floor metal? Starting to get all metal togather before I start anything
ty

_________________
Kiddo if you sold him that piece of crap you atta be frikin ashamed of yourself
Back to top Go down
Big M
Administrator
Administrator
avatar

KNIGHTS ORDER OF THE CCC

ELITE GOLDEN COMMANDO CONTRIBUTOR

Big Block 361



20112016

Posts : 2658
Points : 2677
Reputation : 4
Join date : 2011-11-10
Location : Williams CA

PostSubject: Re: sheet metal?   Mon Jun 25, 2012 3:04 pm

Sheetmetal is 18 Ga. on these cars to my knowledge.

---John

_________________
In Rust, We Trust.
Back to top Go down
Guest
Guest



PostSubject: Re: sheet metal?   Mon Jun 25, 2012 8:49 pm

Ty John is correct, 18 Guage and is very difficult to bend unless you use a medal brake.
Back to top Go down
JAG
Administrator
Administrator
avatar

1st LIEUTENANT OF THE KNIGHTS ORDER OF THE CCC

ELITE GOLDEN COMMANDO CONTRIBUTOR
506/ 505hp Viper V10



2015
Posts : 5177
Points : 5169
Reputation : 5
Join date : 2011-11-18
Age : 32
Location : Syracuse NY

PostSubject: Re: sheet metal?   Mon Jun 25, 2012 11:36 pm

yeah i was a little too late to the party it is 18 gauge
Back to top Go down
crazy58fury
CCC Member
CCC Member
avatar

Posts : 264
Points : 322
Reputation : 0
Join date : 2012-01-26
Age : 23
Location : Rochester, NY

PostSubject: Re: sheet metal?   Tue Jun 26, 2012 5:58 am

Thanks guys, Im just trying to find a place around here that has it, Cant seem to find any,

_________________
Kiddo if you sold him that piece of crap you atta be frikin ashamed of yourself
Back to top Go down
Arnie1964
CCC Member
CCC Member
avatar

"Badass" Poly 318!


Posts : 2514
Points : 3887
Reputation : 0
Join date : 2011-11-08
Age : 71
Location : NC

PostSubject: Re: sheet metal?   Tue Jun 26, 2012 7:26 am

Any place the sells steel products to industry ( angle iron,pipe, channel iron) ect will sell you a sheet. Usuall comes in 4X10 but they might sell you a smaller piece but you will pay a premium for a cut piece. Just look in your yellow pages.

_________________
Back to top Go down
 

sheet metal?

View previous topic View next topic Back to top 
Page 1 of 1

Permissions in this forum:You cannot reply to topics in this forum
The Christine Car Club :: Christine Car Club Tech Section :: Body, Interior & Exterior Trim & Paint:-